電氣柜綜合試驗臺

一、功能特點

多功能試驗臺主要用于低壓電器成套設備的進貨檢驗、出廠檢驗、工程驗收、3C檢查等試驗項目。包括主回路、控制回路的通電操作試驗。電流表、電壓表、電能表（電度表）、有功功率表、無功功率表、功率因數表（相位表）等各檢測回路及測量儀表的檢驗。電容補償控制器自動狀態下投、切試驗、工頻過電壓保護試驗和過電壓電容切除時間的檢測。介電強度試驗，接地電阻的測試等。

電氣柜綜合試驗臺技術指標

  1.三相交流電源380V：輸出三相交流相電壓220V、線電壓380V，zui大輸出電流20A。

2.交直流控制電源：

①輸出三相交流電壓0-690V可調，zui大輸出電流8A。

    ②輸出直流電壓0-250V可調，zui大輸出電流10A。

    ③輸出三相交流控制電壓，即額定電壓和過電壓（UA=UB=UC=220V-275V可調、UAB=UBC=UCA =380V-480V可調），zui大輸出電流8A。

        3、 三相交流電流：輸出三相交流電流0-10A可調，開口電壓6V。三相電流通過轉換開關任意選擇電流與電壓相角分別為+30º、0º、-30º，即“超前”（容性負載）、“同相”（阻性負載）、“滯后”（感性負載）。

        4.補償控制裝置試驗：

           ①利用第2.3項和第3項功能可在控制器自動狀態下進行投、切試驗和過電壓保護試驗。

 ②控制器過電壓時輸出信號全部切除的時間由HHS6A-1型數顯時間繼電器顯示，計時范圍1s - 99min99s。

三、 原有試驗臺改動要求

 1：增加試驗報警裝置（試驗時按下報警按鈕，有聲光報警提示）

2：將原來三相統調和分別調整按鈕改成帶復位旋轉開關，操作更方便

3：建議將三相電源進線用工業三相四線插座安裝在測試臺右側下方，

   所有輸插座或接線柱，改到后面上部，方便于操作

4：將總電源開關改到前面板右下角

5：測試臺兩側配置測試線或電源線收放支架

6：輸出部分建議采用，紅、綠、黃、黑、接線柱，配套帶夾四種2.5mm²x5m

   測試線輸出，便于試驗時，識別三相相序和正負極性。

7：所有儀表一律安裝在測試臺斜面板上，便于操作者監測

四 其他要求

1：測試臺外形，做到便于用戶操作，外形美觀。前面帶有抽棋。外殼表面采用戶外

   灰色塑粉噴涂

2：所有儀表采用三位半0.5級儀表顯示，外形尺寸92x46

3：大電流輸出線50mmx7mx6根一頭帶夾子

4：測試線2.5mm²x5mx8根（紅綠黃黑各兩根），每根線另一頭帶夾子